{"id":97540,"date":"2026-10-27T15:30:44","date_gmt":"2026-10-27T13:30:44","guid":{"rendered":"https:\/\/www.rubi.com\/?p=97540"},"modified":"2026-10-27T16:49:48","modified_gmt":"2026-10-27T14:49:48","slug":"how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts","status":"publish","type":"post","link":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/","title":{"rendered":"How to Maintain and Align Your Wet Tile Saw for Precision Cuts"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">A <strong>wet tile saw<\/strong> can deliver extremely clean, accurate cuts, but only when the machine is setup correctly square, the blade is in good condition, and the water system is doing its job properly. When cuts start to wander, chip more than usual or need correcting after every pass, the cause is rarely just one thing. On site, accuracy usually drops because several small issues have been allowed to build up together.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For professional tilers, the goal is not simply to keep the saw looking tidy. The real aim is to keep the blade running true, the carriage moving smoothly and the tile fully supported from start to finish. If you are reviewing your wider setup, the main<a href=\"https:\/\/www.rubi.com\/en\/sections\/electric-cutting\"> Electric tile cutting<\/a> range is a useful reference point, and different<a href=\"https:\/\/www.rubi.com\/en\/categories\/electric-cutters-and-mitre-saws\"> electric cutters<\/a> will place different demands on alignment, support and blade choice.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Get the routine right and most <strong>tile saws<\/strong> become more predictable, faster to work with and less wasteful on porcelain, ceramic and natural stone. Ignore the basics and even a good saw will start producing poor results.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"1025\" height=\"678\" src=\"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK.jpg\" alt=\"Tiler using a wet saw up close.\" class=\"wp-image-97543\" srcset=\"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK.jpg 1025w, https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK-300x198.jpg 300w, https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK-768x508.jpg 768w\" sizes=\"(max-width: 1025px) 100vw, 1025px\" \/><\/figure>\n\n\n\n<!--HubSpot Call-to-Action Code --><span class=\"hs-cta-wrapper\" id=\"hs-cta-wrapper-ba84cb9c-94c5-46bc-8298-8f62a23f1022\"><span class=\"hs-cta-node hs-cta-ba84cb9c-94c5-46bc-8298-8f62a23f1022\" id=\"hs-cta-ba84cb9c-94c5-46bc-8298-8f62a23f1022\"><!--[if lte IE 8]><div id=\"hs-cta-ie-element\"><\/div><![endif]--><a href=\"https:\/\/cta-redirect.hubspot.com\/cta\/redirect\/6786297\/ba84cb9c-94c5-46bc-8298-8f62a23f1022\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" class=\"hs-cta-img\" id=\"hs-cta-img-ba84cb9c-94c5-46bc-8298-8f62a23f1022\" style=\"border-width:0px;\" src=\"https:\/\/no-cache.hubspot.com\/cta\/default\/6786297\/ba84cb9c-94c5-46bc-8298-8f62a23f1022.png\"  alt=\"* Everything you need to know about RUBI Bridge Saws. Click here and download  the guide\u00a0for free.\"\/><\/a><\/span><script charset=\"utf-8\" src=\"https:\/\/js.hscta.net\/cta\/current.js\"><\/script><script type=\"text\/javascript\"> hbspt.cta.load(6786297, 'ba84cb9c-94c5-46bc-8298-8f62a23f1022', {\"useNewLoader\":\"true\",\"region\":\"na1\"}); <\/script><\/span><!-- end HubSpot Call-to-Action Code -->\n\n\n\n<h2 class=\"wp-block-heading\">Why your wet tile saw stops cutting accurately<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">The warning signs to spot early<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Most accuracy problems show themselves before the saw becomes unusable. The key is recognising the early signs and correcting them before they turn into wasted material.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>The saw pulls off the marked line<\/strong> even when the tile is held correctly against the guide.<\/li>\n\n\n\n<li><strong>One side of the cut chips more heavily than the other<\/strong>, especially on porcelain with a visible glazed face.<\/li>\n\n\n\n<li><strong>The feed feels heavier than normal<\/strong> and the blade seems to drag instead of cutting cleanly.<\/li>\n\n\n\n<li><strong>Water is not hitting both sides of the blade evenly<\/strong>, which often leads to extra heat and rougher edges.<\/li>\n\n\n\n<li><strong>The carriage, tray or guide feels loose<\/strong>, rough or inconsistent from one end of the cut to the other.<\/li>\n\n\n\n<li><strong>Test cuts stop matching<\/strong>, even though your measurements are correct.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">On site, these small changes matter. If the saw starts sounding harsher, vibrating more than usual or leaving a rough exit edge, do not assume it is just the material. A machine that was cutting straight last week does not normally go offline for no reason.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Blade, water flow and setup checks<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Start with the obvious mechanical causes. A worn, glazed or damaged blade will cut slower and deflect more. A blocked pump or partially clogged nozzle will reduce cooling and stop the slurry being cleared properly from the cut. Once that happens, the blade has to work harder and the cut quality and accuracy usually drops with it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Then check the setup itself. If the machine is not setup stable and level, the tray is carrying dried slurry on the rollers, or the fence has been knocked slightly out of parallel during transport, the saw may still run but it will not cut accurately. This is why experienced tilers check the whole machine rather than blaming the blade alone.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Blade choice also matters. Using the wrong blade for the material can make even a well-aligned saw feel poor. If you want to review options, it is worth looking at<a href=\"https:\/\/www.rubi.com\/en\/blog\/diamond-blades\/\"> diamond blades<\/a> in general and more specifically<a href=\"https:\/\/www.rubi.com\/en\/categories\/wet-cutting-diamond-blades\"> wet cutting diamond blades<\/a> for water-cooled machines. For a broader explanation of matching blade type to application, see<a href=\"https:\/\/www.rubi.com\/en\/blog\/a-professional-guide-to-rubi-wet-dry-blades-understanding-the-colour-system\/\"> A Professional Guide to RUBI Wet &amp; Dry Blades: Understanding the Colour System<\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Together with blade choice, the blades are directional and need to be fitted in the correct orientation. All Rubi diamond blades have a rotational arrow laser engraved on the back, this needs to match the arrow on the blade guard. An incorrectly fitted blade will cause inaccurate cuts immediately.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"792\" height=\"528\" src=\"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/52960-dcx-250-xpert-1250-230v-50hz-3-a-rubi.jpg\" alt=\"Tiler using a large wet saw.\" class=\"wp-image-97553\" srcset=\"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/52960-dcx-250-xpert-1250-230v-50hz-3-a-rubi.jpg 792w, https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/52960-dcx-250-xpert-1250-230v-50hz-3-a-rubi-300x200.jpg 300w, https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/52960-dcx-250-xpert-1250-230v-50hz-3-a-rubi-768x512.jpg 768w\" sizes=\"(max-width: 792px) 100vw, 792px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">A maintenance routine for cleaner, straighter cuts<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Cleaning the saw properly after use<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Good maintenance starts as soon as the cutting stops. Leaving slurry in the tray, on the rails or around the pump is one of the fastest ways to shorten the working life of a wet saw. Once that residue dries, it hardens on guides, clogs water passages and makes moving parts less consistent.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A practical end-of-day cleaning routine should include the following:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li><strong>Disconnect the power<\/strong> before touching the blade, pump or moving parts.<\/li>\n\n\n\n<li><strong>Empty the tray fully<\/strong> and remove sludge before it dries into a cement-like deposit.<\/li>\n\n\n\n<li><strong>Rinse the tray, splash guards and cutting table<\/strong> with clean water to remove abrasive residue.<\/li>\n\n\n\n<li><strong>Brush off rails, rollers and guide areas<\/strong> so the carriage can move freely on the next job.<\/li>\n\n\n\n<li><strong>Flush the pump and hoses<\/strong> with clean water to clear out fine particles.<\/li>\n\n\n\n<li><strong>Dry the saw properly<\/strong> before storage, especially if it is being loaded into a van and left overnight.<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">This is not about being precious with the tool. It is about preventing wear in the exact places that affect cut accuracy. A tray full of dried slurry may not look serious, but it can easily affect water delivery, rolling action and fence stability the next time the saw is used.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Looking after the blade, pump and guide system<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The blade deserves its own routine. Inspect it regularly for glazing, uneven wear, visible damage or signs that it has been overheated. If the blade is cutting slowly or pushing harder than usual, dressing it using a Rubi Cleaning block may restore performance. If it is warped, cracked or noticeably unstable, replacement is the only safe option.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The pump and water lines are just as important. Water should reach the blade consistently and cleanly, ideally on both sides of the cutting zone. If one side is dry or weak, the blade can start to run hotter and cut less cleanly. Check the pump filter, remove sediment from the reservoir and make sure the nozzles are pointed where they should be.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Finally, inspect the guide system. Whether your saw uses a sliding tray, a moving head or a rail-guided arrangement, precision depends on smooth travel and minimal play. Clean the guide surfaces, tighten any fasteners that have loosened under vibration and check for wear in rollers, bearings or locking points. A saw can only cut as straight as its most worn moving part.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"768\" height=\"432\" src=\"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/cortar-en-inglete1-1-recortado.jpg\" alt=\"Tiler using a large bridge saw.\" class=\"wp-image-97562\" srcset=\"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/cortar-en-inglete1-1-recortado.jpg 768w, https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/cortar-en-inglete1-1-recortado-300x169.jpg 300w\" sizes=\"(max-width: 768px) 100vw, 768px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">How to align a wet tile saw for precision cuts<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Squaring the blade and table<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Alignment should always begin with the relationship between the blade and the table. If the blade is not square to the cutting surface, every other adjustment becomes a compromise.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Unplug the saw and raise or position the cutting head so you can access the blade safely.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Place a reliable engineer\u2019s square or machinist\u2019s square against the table and bring it up to the blade body. If the blade is segmented, check against the steel core rather than the segment edge. You are looking for full, even contact with no visible gap.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the blade is leaning slightly, adjust the saw according to its design until the blade sits square to the table. Some machines allow adjustment through the head assembly, while others use fixed points and shims. The exact mechanism varies, but the principle stays the same: square first, then lock the setting and re-check it. Do not assume it stayed correct once the bolts were tightened.<\/p>\n\n\n\n<!--HubSpot Call-to-Action Code --><span class=\"hs-cta-wrapper\" id=\"hs-cta-wrapper-d7bdcb50-0f85-44f3-917b-5aba89ffe6a9\"><span class=\"hs-cta-node hs-cta-d7bdcb50-0f85-44f3-917b-5aba89ffe6a9\" id=\"hs-cta-d7bdcb50-0f85-44f3-917b-5aba89ffe6a9\"><!--[if lte IE 8]><div id=\"hs-cta-ie-element\"><\/div><![endif]--><a href=\"https:\/\/cta-redirect.hubspot.com\/cta\/redirect\/6786297\/d7bdcb50-0f85-44f3-917b-5aba89ffe6a9\" ><img decoding=\"async\" class=\"hs-cta-img\" id=\"hs-cta-img-d7bdcb50-0f85-44f3-917b-5aba89ffe6a9\" style=\"border-width:0px;\" src=\"https:\/\/no-cache.hubspot.com\/cta\/default\/6786297\/d7bdcb50-0f85-44f3-917b-5aba89ffe6a9.png\"  alt=\"New call-to-action\"\/><\/a><\/span><script charset=\"utf-8\" src=\"https:\/\/js.hscta.net\/cta\/current.js\"><\/script><script type=\"text\/javascript\"> hbspt.cta.load(6786297, 'd7bdcb50-0f85-44f3-917b-5aba89ffe6a9', {\"useNewLoader\":\"true\",\"region\":\"na1\"}); <\/script><\/span><!-- end HubSpot Call-to-Action Code -->\n\n\n\n<h3 class=\"wp-block-heading\">Aligning the fence or guide<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Once the blade is square, the next step is making sure the fence or guide runs parallel to the blade path. If the guide is pushing the tile into the blade at a slight angle, the saw will bind, chip more aggressively or pull offline during long cuts.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A simple method to check the squareness of a saw only requires the tools to remove a blade, a pencil, tape measure and a new rectified tile.<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Remove the blade from the machine.<\/li>\n\n\n\n<li>Place the new rectified tile on the bed of the cutter against the fence.<\/li>\n\n\n\n<li>Clamp the pencil in the blade flanges so it touched the tile.<\/li>\n\n\n\n<li>Move the cutting head or sliding table so the pencil marks the tile (you will need a small amount of pressure on the pencil)<\/li>\n\n\n\n<li>Measure the edge of the tile to the pencil mark at both end of the tile. If these match the saw is square if not it will need adjusting. Adjustments depend on the machine model.<\/li>\n\n\n\n<li>Accurately mark the tile at each end<\/li>\n\n\n\n<li>For Rubi bridge saws loosen the bolts holding the fence in place, line the pencil with the marks on the tile and adjust the fence to the tile. Retighten the bolts.<\/li>\n\n\n\n<li>Recheck the pencil mark, if accurate remove the pencil and refit the blade (correct orientation).<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">On sliding tray saws such as the DT-250 Max, the checking square follows the same steps as above, the adjustment is on the runners under the table by loosening the bolts that hold the runners in place and move the table to align the marks and retighten the bolts.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Confirming the setup with a test cut<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Never finish an alignment by eye alone. Use a test cut on a new tile so there is a factory edge to measure from.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">After cutting, measure both ends of the tile which should match on a properly aligned machine. A properly aligned saw normally feeds more smoothly, exits the tile more cleanly and produces less chatter.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This is also the stage where you confirm the setup under real working conditions. If the saw is square in the workshop but starts wandering once a larger tile is loaded onto it, support may be the missing part of the process. Straight cuts are the foundation for more demanding shapes, and once the setup is correct, more advanced work becomes far easier. For that next step, see<a href=\"https:\/\/www.rubi.com\/en\/blog\/cutting-complex-shapes-how-to-achieve-intricate-tile-cuts-with-rubi\/\"> Cutting Complex Shapes: How to Achieve Intricate Tile Cuts with RUBI<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Common mistakes to avoid on site<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Feed pressure, vibration and unstable setup<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">One of the most common mistakes with <strong>wet saws<\/strong> is trying to force the cut when the machine starts to slow down. Excessive feed pressure does not save time. It usually increases blade deflection, raises the chance of chipping and puts unnecessary load on the motor, bearings and guide system.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The saw and blade should do the work not the operator. Your job is to keep the tile stable, maintain a steady feed and let the blade work at a controlled rate. If resistance increases, stop and check the blade, water flow and alignment instead of pushing harder.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Vibration is another major problem. Even a well-aligned <strong>wet tile saw<\/strong> will cut poorly if it is sitting on an uneven surface, if the stand has movement in it, or if a large tile is hanging unsupported off one side. Long porcelain pieces are especially sensitive to this. If the tile flexes during the cut, the blade will not stay in a clean, predictable path.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">When the saw needs repair rather than adjustment<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Not every accuracy problem can be solved by cleaning and re-aligning. Sometimes the machine is simply worn beyond what adjustment can compensate for. That is usually the case when you see one or more of the following:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Persistent blade wobble<\/strong> even after fitting a sound blade correctly.<\/li>\n\n\n\n<li><strong>Noticeable play in the arbour, carriage or tray<\/strong> that returns immediately after tightening.<\/li>\n\n\n\n<li><strong>Rough bearing noise<\/strong> from the motor or moving head.<\/li>\n\n\n\n<li><strong>A fence or locking guide that will not hold position<\/strong> during the cut.<\/li>\n\n\n\n<li><strong>A pump that still delivers poor flow after cleaning<\/strong>, suggesting wear or internal failure.<\/li>\n\n\n\n<li><strong>Cracked, bent or distorted support components<\/strong> that prevent repeatable alignment.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">At that point, adjustment becomes a temporary workaround rather than a proper fix. A professional saw should stay square, hold its settings and cut repeatably. If it does not, the right decision may be repair, replacement of worn parts or a full service rather than another round of minor corrections.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In practice, cleaner and straighter cuts come from discipline more than luck. Keep the saw clean, keep the blade matched to the material and sharp, keep the water flowing properly and check alignment before poor cuts start costing you money. When those basics are under control, a wet tile saw becomes what it should be on site: a dependable precision tool rather than a constant source of correction work.<\/p>\n\n\n\n<!--HubSpot Call-to-Action Code --><span class=\"hs-cta-wrapper\" id=\"hs-cta-wrapper-54f67028-4bb1-41e8-b74f-b40b1a3a62e8\"><span class=\"hs-cta-node hs-cta-54f67028-4bb1-41e8-b74f-b40b1a3a62e8\" id=\"hs-cta-54f67028-4bb1-41e8-b74f-b40b1a3a62e8\"><!--[if lte IE 8]><div id=\"hs-cta-ie-element\"><\/div><![endif]--><a href=\"https:\/\/cta-redirect.hubspot.com\/cta\/redirect\/6786297\/54f67028-4bb1-41e8-b74f-b40b1a3a62e8\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" class=\"hs-cta-img\" id=\"hs-cta-img-54f67028-4bb1-41e8-b74f-b40b1a3a62e8\" style=\"border-width:0px;\" src=\"https:\/\/no-cache.hubspot.com\/cta\/default\/6786297\/54f67028-4bb1-41e8-b74f-b40b1a3a62e8.png\"  alt=\"New call-to-action\"\/><\/a><\/span><script charset=\"utf-8\" src=\"https:\/\/js.hscta.net\/cta\/current.js\"><\/script><script type=\"text\/javascript\"> hbspt.cta.load(6786297, '54f67028-4bb1-41e8-b74f-b40b1a3a62e8', {\"useNewLoader\":\"true\",\"region\":\"na1\"}); <\/script><\/span><!-- end HubSpot Call-to-Action Code -->\n","protected":false},"excerpt":{"rendered":"<p>A wet tile saw can deliver extremely clean, accurate cuts, but only when the machine is setup correctly square, the blade is in good condition, and the water system is doing its job properly. When cuts start to wander, chip more than usual or need correcting after every pass, the cause is rarely just one &hellip; <a href=\"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/\">Continued<\/a><\/p>\n","protected":false},"author":37,"featured_media":97543,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"content-type":"","footnotes":""},"categories":[245,119,118],"tags":[3071,356,3069,3068,3070,822,823,1053,1597],"coauthors":[2913],"class_list":["post-97540","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-other-tiling-issues","category-rubi-tools","category-tips-tricks","tag-bridge-saws","tag-electric-cutter","tag-maintaining","tag-maintenance","tag-repairs","tag-rubi-tools","tag-tile-cutter","tag-tiling-tips","tag-wet-saws"],"acf":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.1 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>How to Maintain and Align a Wet Tile Saw<\/title>\n<meta name=\"description\" content=\"Learn how to maintain and align a wet tile saw for cleaner, straighter cuts. A practical and accurate guide for tile professionals.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/\" \/>\n<meta property=\"og:locale\" content=\"en_GB\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Maintain and Align a Wet Tile Saw\" \/>\n<meta property=\"og:description\" content=\"Learn how to maintain and align a wet tile saw for cleaner, straighter cuts. A practical and accurate guide for tile professionals.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/\" \/>\n<meta property=\"og:site_name\" content=\"Welcome to the RUBI Tools Blog!\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.instagram.com\/rubitools\/\" \/>\n<meta property=\"article:published_time\" content=\"2026-10-27T13:30:44+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-10-27T14:49:48+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"1025\" \/>\n\t<meta property=\"og:image:height\" content=\"678\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Emily\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@RubiTools_Es\" \/>\n<meta name=\"twitter:site\" content=\"@RubiTools_Es\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Emily\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"10 minutes\" \/>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Maintain and Align a Wet Tile Saw","description":"Learn how to maintain and align a wet tile saw for cleaner, straighter cuts. A practical and accurate guide for tile professionals.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/","og_locale":"en_GB","og_type":"article","og_title":"How to Maintain and Align a Wet Tile Saw","og_description":"Learn how to maintain and align a wet tile saw for cleaner, straighter cuts. A practical and accurate guide for tile professionals.","og_url":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/","og_site_name":"Welcome to the RUBI Tools Blog!","article_publisher":"https:\/\/www.instagram.com\/rubitools\/","article_published_time":"2026-10-27T13:30:44+00:00","article_modified_time":"2026-10-27T14:49:48+00:00","og_image":[{"width":1025,"height":678,"url":"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK.jpg","type":"image\/jpeg"}],"author":"Emily","twitter_card":"summary_large_image","twitter_creator":"@RubiTools_Es","twitter_site":"@RubiTools_Es","twitter_misc":{"Written by":"Emily","Est. reading time":"10 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"WebPage","@id":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/","url":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/","name":"How to Maintain and Align a Wet Tile Saw","isPartOf":{"@id":"https:\/\/www.rubi.com\/en\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/#primaryimage"},"image":{"@id":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/#primaryimage"},"thumbnailUrl":"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK.jpg","datePublished":"2026-10-27T13:30:44+00:00","dateModified":"2026-10-27T14:49:48+00:00","description":"Learn how to maintain and align a wet tile saw for cleaner, straighter cuts. A practical and accurate guide for tile professionals.","breadcrumb":{"@id":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/#breadcrumb"},"inLanguage":"en-GB","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/"]}]},{"@type":"ImageObject","inLanguage":"en-GB","@id":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/#primaryimage","url":"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK.jpg","contentUrl":"https:\/\/www.rubi.com\/en\/blog\/wp-content\/uploads\/2026\/10\/45986-nd-7-in-max-120v-60hz-usa-2-a-rubi-OK.jpg","width":1025,"height":678},{"@type":"BreadcrumbList","@id":"https:\/\/www.rubi.com\/en\/blog\/how-to-maintain-and-align-your-wet-tile-saw-for-precision-cuts\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.rubi.com\/en"},{"@type":"ListItem","position":2,"name":"How to Maintain and Align Your Wet Tile Saw for Precision Cuts"}]},{"@type":"WebSite","@id":"https:\/\/www.rubi.com\/en\/#website","url":"https:\/\/www.rubi.com\/en\/","name":"Welcome to the RUBI Tools Blog!","description":"","publisher":{"@id":"https:\/\/www.rubi.com\/en\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.rubi.com\/en\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-GB"},{"@type":"Organization","@id":"https:\/\/www.rubi.com\/en\/#organization","name":"RUBI Tools English","url":"https:\/\/www.rubi.com\/en\/","logo":{"@type":"ImageObject","inLanguage":"en-GB","@id":"https:\/\/www.rubi.com\/en\/#\/schema\/logo\/image\/","url":"https:\/\/www.rubi.com\/fr\/blog\/wp-content\/uploads\/2021\/09\/rubi-logo-new.png","contentUrl":"https:\/\/www.rubi.com\/fr\/blog\/wp-content\/uploads\/2021\/09\/rubi-logo-new.png","width":300,"height":300,"caption":"RUBI Tools English"},"image":{"@id":"https:\/\/www.rubi.com\/en\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.instagram.com\/rubitools\/","https:\/\/x.com\/RubiTools_Es","https:\/\/www.linkedin.com\/company\/rubi-group\/","https:\/\/www.youtube.com\/c\/ClubRubi"]}]}},"_links":{"self":[{"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/posts\/97540","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/users\/37"}],"replies":[{"embeddable":true,"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/comments?post=97540"}],"version-history":[{"count":1,"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/posts\/97540\/revisions"}],"predecessor-version":[{"id":97573,"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/posts\/97540\/revisions\/97573"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/media\/97543"}],"wp:attachment":[{"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/media?parent=97540"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/categories?post=97540"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/tags?post=97540"},{"taxonomy":"author","embeddable":true,"href":"https:\/\/www.rubi.com\/en\/blog\/wp-json\/wp\/v2\/coauthors?post=97540"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}